InControl Touch Pro 20B released

All Range Rover Velar related discussions
Jaron787
Posts: 3
Joined: Sun Jul 05, 2020 9:50 am
Location: UK

Re: InControl Touch Pro 20B released

Post by Jaron787 » Mon Jul 27, 2020 7:41 pm

My brand new 2020 Velar seems to be stuck on 19B (last updated 12/2/2020). When I select check for update I just get “Software up to date”

Any ideas what I need to do to start receiving the new software?

GSudhir
Posts: 126
Joined: Sun Dec 30, 2018 11:59 pm
Location: UK

Re: InControl Touch Pro 20B released

Post by GSudhir » Mon Jul 27, 2020 10:14 pm

I had the pop up for the install today for 20B and got it installed today.
Apart from the change in soft controls for the drive mode settings, I haven't seen any major differences. However, I noticed that the suspension didn't drop to access height when I opened the door. I thought this must be something to do with the upgrade being completed only on the next reboot.
Later, I went back to the car to check up on the completed installation and reboot; the car had completed installation and booted up with 20B and the rotary control was not controlling the vehicle settings as expected. But the ride height did not drop this time either when I opened the car! I shall check this again tomorrow.
Any one else experienced this issue?
D300 R Dynamic HSE in Corris Grey with 1033 21 inch alloys
Pano sun roof
Configurable ambient lighting
360 camera
Windsor perforated leather- heated, cooled massage seats

GSudhir
Posts: 126
Joined: Sun Dec 30, 2018 11:59 pm
Location: UK

Re: InControl Touch Pro 20B released

Post by GSudhir » Mon Jul 27, 2020 10:17 pm

Jaron787 wrote:
Mon Jul 27, 2020 7:41 pm
My brand new 2020 Velar seems to be stuck on 19B (last updated 12/2/2020). When I select check for update I just get “Software up to date”

Any ideas what I need to do to start receiving the new software?
Your dealer needs to enable SOTA (software over the air) updates for it to happen. Please give them a ring to get that done.They should be able to do it remotely.
D300 R Dynamic HSE in Corris Grey with 1033 21 inch alloys
Pano sun roof
Configurable ambient lighting
360 camera
Windsor perforated leather- heated, cooled massage seats

Simonh
Posts: 610
Joined: Thu Jul 18, 2019 9:44 pm
Location: Shropshire, UK

Re: InControl Touch Pro 20B released

Post by Simonh » Tue Jul 28, 2020 8:27 am

GSudhir wrote:
Mon Jul 27, 2020 10:14 pm
I had the pop up for the install today for 20B and got it installed today.
Apart from the change in soft controls for the drive mode settings, I haven't seen any major differences. However, I noticed that the suspension didn't drop to access height when I opened the door. I thought this must be something to do with the upgrade being completed only on the next reboot.
Later, I went back to the car to check up on the completed installation and reboot; the car had completed installation and booted up with 20B and the rotary control was not controlling the vehicle settings as expected. But the ride height did not drop this time either when I opened the car! I shall check this again tomorrow.
Any one else experienced this issue?
Has the option been un-selected in the vehicle settings? I noticed the Reverse Traffic warning setting had been in-selected on mine post update.
Velar HSE D240 - MY19
Served by the excellent Shukers Land Rover of Ludlow - 20 years of amazing customer service.

Barneyboo7
Posts: 14
Joined: Mon Jul 13, 2020 3:14 pm
Location: UK

Re: InControl Touch Pro 20B released

Post by Barneyboo7 » Tue Jul 28, 2020 9:42 am

new to the velar world, can someone tell me how i do the update please?

Jaron787
Posts: 3
Joined: Sun Jul 05, 2020 9:50 am
Location: UK

Re: InControl Touch Pro 20B released

Post by Jaron787 » Tue Jul 28, 2020 10:39 am

GSudhir wrote:
Mon Jul 27, 2020 10:17 pm
Jaron787 wrote:
Mon Jul 27, 2020 7:41 pm
My brand new 2020 Velar seems to be stuck on 19B (last updated 12/2/2020). When I select check for update I just get “Software up to date”

Any ideas what I need to do to start receiving the new software?
Your dealer needs to enable SOTA (software over the air) updates for it to happen. Please give them a ring to get that done.They should be able to do it remotely.
I spoke to my dealership and they said if I get the "Software up to date" message, no update is available and according to Land Rover's main website - 19B is still only available in the UK
https://www.landrover.co.uk/ownership/i ... index.html

Where do you get information about 20B from?

ChrisL
Posts: 32
Joined: Sun Jun 16, 2019 12:59 pm
Location: United Kingdom

Re: InControl Touch Pro 20B released

Post by ChrisL » Tue Jul 28, 2020 11:49 am

The last release was being downloaded widely in the UK as reported here but my message stuck firmly to the up to date message until one day it was suddenly downloaded. Took around two weeks. The consensus was that the release was phased to reduce server load. This time around I have received the update today. As usual the dealer is being economical with the truth, there is no update available- for your vehicle yet.

Jaron787
Posts: 3
Joined: Sun Jul 05, 2020 9:50 am
Location: UK

Re: InControl Touch Pro 20B released

Post by Jaron787 » Tue Jul 28, 2020 12:14 pm

ChrisL wrote:
Tue Jul 28, 2020 11:49 am
The last release was being downloaded widely in the UK as reported here but my message stuck firmly to the up to date message until one day it was suddenly downloaded. Took around two weeks. The consensus was that the release was phased to reduce server load. This time around I have received the update today. As usual the dealer is being economical with the truth, there is no update available- for your vehicle yet.
I never received 19C or 20A either though and neither of those release candidates are listed on the JLR website?

liben96
Posts: 357
Joined: Sat Jan 06, 2018 9:19 am
Location: Gib

Re: InControl Touch Pro 20B released

Post by liben96 » Tue Jul 28, 2020 3:02 pm

I updated my car in December to 19B over the air.
Since then I was constantly getting the ‘software is up to date’ message, and I knew that there were new versions 19C, 19D, 20A and 20B.
Yesterday I called them and they enabled it again. Then I was able to install 20B.

Apparently they have to enable it every time there is a new release. At least that is what I have been told...

zani
Posts: 43
Joined: Fri Oct 26, 2018 10:48 am
Location: DE

Re: InControl Touch Pro 20B released

Post by zani » Tue Jul 28, 2020 4:32 pm

Got it yesterday updated we have it in Germany now everything is like you guys said so far so good

Post Reply